| Experiments Home |
|
| Renewable Energy |
|
|
| Photovoltaic Module & Array |
|
|
|
|
  |
 The Solar Car Book A complete kit for making a cool solar racecar. Everything is included: wheels, axles, motors, wires and a genuine one-volt solar cell. |
|
|
Photovoltaics Projects & Experiments
In the field of photovoltaics, a photovoltaic module is a packaged interconnected assembly of photovoltaic cells, also known as solar cells. An installation of photovoltaic modules or panels is known as a photovoltaic array. Photovoltaic cells typically require protection from the environment. For cost and practicality reasons a number of cells are connected electrically and packaged in a photovoltaic module, while a collection of these modules that are mechanically fastened together, wired, and designed to be a field-installable unit, sometimes with a glass covering and a frame and backing made of metal, plastic or fiberglass, are known as a photovoltaic panel or simply solar panel. A photovoltaic installation typically includes an array of photovoltaic modules or panels, an inverter, batteries (for off grid) and interconnection wiring.
Theory and constructionThe majority of modules use wafer-based Crystalline silicon cells or a thin film cell based on cadmium telluride or silicon (see photovoltaic cells for details). In order to use the cells in practical applications, they must be:
Most modules are rigid, but there are some flexible modules available, based on thin film cells. Electrical connections are made in series to achieve a desired output voltage and/or in parallel to provide a desired amount of current source capability. Diodes are included to avoid overheating of cells in case of partial shading. Since cell heating reduces the operating efficiency it is desirable to minimize the heating. Very few modules incorporate any design features to decrease temperature, however installers try to provide good ventilation behind the module, New designs of module include concentrator modules in which the light is concentrated by an array of lenses or mirrors onto an array of small cells. This allows the use of cells with a very high cost per unit area (such as gallium arsenide) in a cost-competitive way. Depending on construction the photovoltaic can cover a range of frequencies of light and can produce electricity from them, but cannot cover the entire solar spectrum. Hence much of incident sunlight energy is wasted when used for solar panels, although they can give far higher efficiencies if illuminated with monochromatic light. Another design concept is to split the light into different wavelength ranges and direct the beams onto different cells tuned to the appropriate wavelength ranges. [1] This is projected to raise efficiency to 50%. Sunlight conversion rates (module efficiencies) can vary from 5-18% in commercial production. Rigid thin-film modulesIn rigid thin film modules, the cell and the module are manufactured in the same production line. The cell is created directly on a glass substrate or superstrate, and the electrical connections are created in situ, a so called "monolithic integration". The substrate or superstrate is laminated with an encapsulant to a front or back sheet, usually another sheet of glass. The main cell technologies in this category are CdTe, amorphous silicon, micromorphous silicon (alone or tandem), or CIGS (or variant). Amorphous silicon has a sunlight conversion rate of 5-9%. Flexible thin-film modulesFlexible thin film cells and modules are created on the same production line by depositing the photoactive layer and other necessary layers on a flexible substrate. If the substrate is an insulator (e.g. polyester or polyimide film) then monolithic integration can be used. If it is a conductor then another technique for electrical connection must be used. The cells are assembled into modules by laminating them to a transparent colourless fluoropolymer on the front side (typically ETFE or FEP) and a polymer suitable for bonding to the final substrate on the other side. The only commercially available (in MW quantities) flexible module uses amorphous silicon triple junction (from Unisolar). ReferencesSee also
External links
Photovoltaic Array 
A photovoltaic array is a linked collection of photovoltaic modules, which are in turn made of multiple interconnected solar cells. The cells convert solar energy into direct current electricity via the photovoltaic effect. The power that one module can produce is seldom enough to meet requirements of a home or a business, so the modules are linked together to form an array. Most PV arrays use an inverter to convert the DC power produced by the modules into alternating current that can plug into the existing infrastructure to power lights, motors, and other loads. The modules in a PV array are usually first connected in series to obtain the desired voltage; the individual strings are then connected in parallel to allow the system to produce more current. Solar arrays are typically measured by the electrical power they produce, in watts, kilowatts, or even megawatts.
ApplicationsIn urban and suburban areas, photovoltaic arrays are commonly used on rooftops to measure power use; often the building will have a preexisting connection to the power grid, in which case the energy produced by the PV array will be sold back to the utility in some sort of net metering agreement. In more rural areas, ground-mounted PV systems are more common. The systems may also be equipped with a battery backup system to compensate for a potentially unreliable power grid. In agricultural settings, the array may be used to directly power DC pumps, without the need for an inverter. In remote settings such as mountainous areas, islands, or other places where a power grid is unavailable, solar arrays can be used as the sole source of electricity, usually by charging a storage battery. Satellites use solar arrays for their power. In particular the International Space Station uses multiple solar arrays to power all the equipment on board. Solar photovoltaic panels are frequently applied in satellite power. However, costs of production have been reduced in recent years for more widespread use through production and technological advances. For example, single crystal silicon solar cells have largely been replaced by less expensive multicrystalline silicon solar cells, and thin film silicon solar cells have also been developed recently at lower costs of production yet (see Solar cell). Although they are reduced in energy conversion efficiency from single crystalline Si wafers, they are also much easier to produce at comparably lower costs. Together with a storage battery, photovoltaics have become commonplace for certain low-power applications, such as signal buoys or devices in remote areas or simply where connection to the electricity mains would be impractical. In experimental form they have even been used to power automobiles in races such as the World solar challenge across Australia. Many yachts and land vehicles use them to charge on-board batteries. PV performance
At high noon on a cloudless day at the equator, the power of the sun is about 1 kW/m², on the Earth's surface, to a plane that is perpendicular to the sun's rays. As such, PV arrays can track the sun through each day to greatly enhance energy collection. However, tracking devices add cost, and require maintenance, so it is more common for PV arrays to have fixed mounts that tilt the array and face due South in the Northern Hemisphere (in the Southern Hemisphere, they should point due North). The tilt angle, from horizontal, can be varied for season, but if fixed, should be set to give optimal array output during the peak electrical demand portion of a typical year. For large systems, the energy gained by using tracking systems outweighs the added complexity (trackers can increase efficiency by 30% or more). PV arrays that approach or exceed one megawatt often use solar trackers. Accounting for clouds, and the fact that most of the world is not on the equator, and that the sun sets in the evening, the correct measure of solar power is insolation – the average number of kilowatt-hours per square meter per day. For the weather and latitudes of the United States and Europe, typical insolation ranges from 4 kWh/m²/day in northern climes to 6.5 kWh/m²/day in the sunniest regions. Typical solar panels have an average efficiency of 12%, with the best commercially available panels at 20%. Thus, a photovoltaic installation in the southern latitudes of Europe or the United States may expect to produce 1 kWh/m²/day. A typical "150 watt" solar panel is about a square meter in size. Such a panel may be expected to produce 1 kWh every day, on average, after taking into account the weather and the latitude. In the Sahara desert, with less cloud cover and a better solar angle, one can obtain closer to 8.3 kWh/m²/day. The unpopulated area of the Sahara desert is over 9 million km², which if covered with solar panels would provide 630 terawatts total power. The Earth's current energy consumption rate is around 13.5 TW at any given moment (including oil, gas, coal, nuclear, and hydroelectric). Other factors affect PV performance. Photovoltaic cells' electrical output is extremely sensitive to shading. When even a small portion of a cell, module, or array is shaded, while the remainder is in sunlight, the output falls dramatically due to internal 'short-circuiting' (the electrons reversing course through the shaded portion of the p-n junction). Therefore it is extremely important that a PV installation is not shaded at all by trees, architectural features, flag poles, or other obstructions. Sunlight can be absorbed by dust, fallout, or other impurities at the surface of the module. This can cut down the amount of light that actually strikes the cells by as much as half. Maintaining a clean module surface will increase output performance over the life of the module. Module output and life are also degraded by increased temperature. Allowing ambient air to flow over, and if possible behind, PV modules reduces this problem. However, effective module lives are typically 25 years or more [1], so replacement costs should be considered as well. Solar photovoltaic panels on spacecraft
Solar panels can be used on spacecraft, particularly when they are in the inner part of the solar system. They have been designed to pivot on spacecraft, so that they will always be in the direct path of solar rays. In order to optimize the amount of energy generated, solar panels on spacecraft can be equipped with a Fresnel lens, which concentrates sunlight. Because of these efforts to maximize electric production, and the fact that the Sun is mostly the only source of energy, the construction of solar cells on spacecraft could be one of the highest costs. When journeying to outer parts of the solar system (or beyond), nuclear reactors or radioisotope thermal generators are preferred, as the Sun's rays are too weak at such extreme distances to power a spacecraft. The ESA is researching the possibility of solar power satellites that would generate electricity in space and then beam it to Earth via laser or microwaves. In addition, solar power is being considered for use as a propulsion mechanism in lieu of chemical propulsion. See also
Notes
This article is licensed under the GNU Free Documentation License. It uses material from Wikipedia Encyclopedia article "Photovoltaic Module" |
